Can I Install A Bathtub Myself?
Can I Install A Bathtub Myself?
Blog Article
The author is making a few good pointers on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this great article just below.
Installing a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging task. If the old bathtub is readily available, the project can move immediately; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. Instead of employing a professional to take over a halfway-completed project, it is better to think about employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have already bought a new tub and also do not require to transform the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water and inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the tub as well as additionally examine the overflow outlet and the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a stiff seal, causing the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog post about Installing A Bathtub when doing a lookup on the search engines. If you liked our post please don't forget to pass it around. Thanks so much for going through it.
Book Your Appointment
Report this page